List of BSNL Broadband Errors in DSL Technology

On connecting the Broadband Services, with ADSL type technology via ADSL Modem to enable the faster data transmission over copper telephone lines by using Bridge mode (or dialer mode), many of the customers are getting the Asymmetric digital subscriber line (ADSL) Broadband Line connecting error codes 619, 629, 631, 633, 645, 650, 651, 678, 680, 691, 718, 721 in frequent.

BSNL Broadband Error Codes

Every Broadband customer at least once enables in most frequent through DSL/ADSL Modem (CPE) in Broadband Services, for this problems, we have already presented with some possible solutions and now we are presented total broadband error codes as follows most occurred Broadband Error Codes with possible solutions.

Most Frequently Occurred BSNL Broadband Error Codes

Error code 619 – The port is disconnected

629 – The port was disconnected by the remote machine

631 – The port was disconnected by the user

633 – The port is already in use or is not configured for Remote Access

645 – Internal authentication Error

650 – The Remote Access server is not responding – It occurs, if the ISP server modem/equipment is not set up properly.

651 – Your modem (or other connecting device) has reported an Error

678 – There is no answer

680 – No dial tone

691 – Access denied because username and/or password is invalid on the domain

721 – Remote PPPoE peer is not responding

718 – PPP timeout

Total / Other Broadband Error Codes

600 – An operation is pending.

601 – The port handle is invalid.

602 – The port is already open.

603 – Caller’s buffer is too small.

604 – Wrong information specified.

605 – Cannot set port information.

606 – The port is not connected.

607 – The event is invalid.

608 – The device does not exist.

609 – The device type does not exist.

610 – The buffer is invalid.

611 – The route is not available.

612 – The route is not allocated.

613 – Invalid compression specified.

614 – Out of buffers.

615 – The port was not found.

616 – An asynchronous request is pending.

617 – The port or device is already disconnecting.

618 – The port is not open.

619 – The port is disconnected.

620 – There are no endpoints.

621 – Cannot open the phone book file.

622 – Cannot load the phone book file.

623 – Cannot find the phone book entry.

624 – Cannot write the phone book file.

625 – Invalid information found in the phone book.

626 – Cannot load a string.

627 – Cannot find key.

628 – The port was disconnected.

629 – The port was disconnected by the remote machine.

630 – The port was disconnected due to hardware failure.

631 – The port was disconnected by the user.

632 – The structure size is incorrect.

633 – The port is already in use or is not configured for Remote Access dialout.

634 – Cannot register your computer on the remote network.

635 – Unknown Error.

636 – The wrong device is attached to the port.

637 – The string could not be converted.

638 – The request has timed out.

639 – No Asynchronous net available.

640 – A NetBIOS Error has occurred.

641 – The server cannot allocate NetBIOS resources needed to support the client.

642 – One of your NetBIOS names is already registered on the remote network.

643 – A network adapter at the server failed.

644 – You will not receive network message popups.

645 – Internal authentication Error.

646 – The account is not permitted to log on at this time of day.

647 – The account is disabled.

648 – The password has expired.

649 – The account does not have Remote Access permission.

650 – The Remote Access server is not responding.

651 – Your modem (or other connecting device) has reported an Error.

652 – Unrecognized response from the device.

653 – A macro required by the device was not found in the device .INF file section.

654 – A command or response in the device .INF file section refers to an undefined macro

655 – The macro was not found in the device .INF file section.

656 – The macro in the device .INF file section contains an undefined macro

657 – The device .INF file could not be opened.

658 – The device name in the device .INF or media .INI file is too long.

659 – The media .INI file refers to an unknown device name.

660 – The device .INF file contains no responses for the command.

661 – The device .INF file is missing a command.

662 – Attempted to set a macro not listed in device .INF file section.

663 – The media .INI file refers to an unknown device type.

664 – Cannot allocate memory.

665 – The port is not configured for Remote Access.

666 – Your modem (or other connecting device) is not functioning.

667 – Cannot read the media .INI file.

668 – The connection dropped.

669 – The usage parameter in the media .INI file is invalid.

670 – Cannot read the section name from the media .INI file.

671 – Cannot read the device type from the media .INI file.

672 – Cannot read the device name from the media .INI file.

673 – Cannot read the usage from the media .INI file.

674 – Cannot read the maximum connection BPS rate from the media .INI file.

675 – Cannot read the maximum carrier BPS rate from the media .INI file.

676 – The line is busy.

677 – A person answered instead of a modem.

678 – There is no answer.

679 – Cannot detect carrier.

680 – There is no dial tone.

681 – General Error reported by device.

682 – ERROR WRITING SECTIONNAME

683 – ERROR WRITING DEVICETYPE

684 – ERROR WRITING DEVICENAME

685 – ERROR WRITING MAXCONNECTBPS

686 – ERROR WRITING MAXCARRIERBPS

687 – ERROR WRITING USAGE

688 – ERROR WRITING DEFAULTOFF

689 – ERROR READING DEFAULTOFF

690 – ERROR EMPTY INI FILE

691 – Access denied because username and/or password is invalid on the domain.

692 – Hardware failure in port or attached device.

693 – ERROR NOT BINARY MACRO

694 – ERROR DCB NOT FOUND

695 – ERROR STATE MACHINES NOT STARTED

696 – ERROR STATE MACHINES ALREADY STARTED

697 – ERROR PARTIAL RESPONSE LOOPING

698 – A response keyname in the device .INF file is not in the expected format.

699 – The device response caused buffer overflow.

700 – The expanded command in the device .INF file is too long.

701 – The device moved to a BPS rate not supported by the COM driver.

702 – Device response received when none expected.

703 – ERROR INTERACTIVE MODE

704 – ERROR BAD CALLBACK NUMBER

705 – ERROR INVALID AUTH STATE

706 – ERROR WRITING INITBPS

707 – X.25 diagnostic indication.

708 – The account has expired.

709 – Error changing password on domain.

710 – Serial overrun Errors were detected while communicating with your modem.

711 – RasMan initialization failure. Check the event log.

712 – Biplex port is initializing. Wait a few seconds and redial.

713 – No active ISDN lines are available.

714 – Not enough ISDN channels are available to make the call.

715 – Too many Errors occurred because of poor phone line quality.

716 – The Remote Access IP configuration is unusable.

717 – No IP addresses are available in the static pool of Remote Access IP addresses.

718 – PPP timeout.

719 – PPP terminated by remote machine.

720 – No PPP control protocols configured.

721 – Remote PPP peer is not responding.

722 – The PPP packet is invalid.

723 – The phone number, including prefix and suffix, is too long.

724 – The IPX protocol cannot dial-out on the port because the computer is an IPX router.

725 – The IPX protocol cannot dial-in on the port because the IPX router is not installed..

726 – The IPX protocol cannot be used for dial-out on more than one port at a time.

727 – Cannot access TCPCFG.DLL.

728 – Cannot find an IP adapter bound to Remote Access.

729 – SLIP cannot be used unless the IP protocol is installed.

730 – Computer registration is not complete.

731 – The protocol is not configured.

732 – The PPP negotiation is not converging.

733 – The PPP control protocol for this network protocol is not available on the server.

734 – The PPP link control protocol terminated..

735 – The requested address was rejected by the server..

736 – The remote computer terminated the control protocol.

737 – Loopback detected..

738 – The server did not assign an address.

739 – The remote server cannot use the Windows NT encrypted password.

740 – The TAPI devices configured for Remote Access failed to initialize or were not installed correctly.

741 – The local computer does not support encryption.

742 – The remote server does not support encryption.

743 – The remote server requires encryption.

744 – Cannot use the IPX net number assigned by the remote server. Check the event log.

752 – A syntax Error was encountered while processing a script.

The above are the total list of BSNL Broadband Line Connecting Error Codes in DSL Technology.

LEAVE A REPLY

Please enter your comment!
Please enter your name here